AC Repair In Brandon, FL

No cooling, system running upon arrival, however, compressor is rattling very loud and not pumping refrigerant. Then compressor shut off on overload. Got compressor to cool down and compressor started up. OK however start up amps were very high. Also static pressure very high on system, even with lower merv filter in it. Cold air return is undersized. Need to change 16 inch flex to 18 inch flex and 9 inch flex 10 inch flex. Also recommended replacing compressor. Compressor still under parts warranty. System was never registered by company who installed it so there is only a five year parts warranty. System is running and operating at this time, however, it will go out again. Client is going to try to have company who installed system to come back and fix return and make other repairs.

Found system tripping out on high head pressure Removed charge again to still find restriction in 3/8 copper piping at air handler. Removed pipe and repaired with new. Pulled 497 micron vac and checked charge again. System ran for almost 45 mins dropped temp down in home from 80-77 before leaving and pressures never sky rocketed. Believe this is the final fix for this system

Arrived and client stated that he had AND Services out and they stated he needed a new drain line. Found drain line cleared but client was using a highly restricted filter. Removed filter to find system to start draining properly! Client is going to sign up for membership

Arrived to find lose connections at condenser Repaired and tested system all okay at this time

2.5 Ton Carrier 14.3 SEER2 Heat Pump - Hurricane pad - Hurricane straps - Locking caps - T6 Thermostat - 5kw Electric heater - SS2 Float switch - 10 year part warranty - 1 year labor warranty - 1 year prime membership

Client had another company replaced their system a couple of months ago. Client was having nothing but problems with the system and is having old company remove unit and having us replace it with a 2 1/2 ton Carrier heat pump system. Inspected ductwork in attic and advised client that ductwork should be replaced along with the proper IAQ. There is biological growth buildup in ductwork, along with some air leakage. Ductwork is most likely original to when the house was built. Client just wants to replace system for now and possibly do the ductwork six months to a year down the road. Scheduled install for Friday, June 13. Client finance full amount.

I did the changeout

Task Includes -Replacement of out of warranty variable speed blower motor -Replacement of out of warranty control module

Sent estimate for new blower motor and control module

Came out for machine not turning on upon arrival found fuse was bad from error code after checking over all reasons of why the fuse was blowing found a bad thermostat. Replaced thermostat and machine now is operating correctly.

Arrived to find burnt wires to condenser and burnt disconnect. Advised client system is really old and could have more issues. Client invested in band aid repairs After replacement of disconnect the compressor contactor was welded from the burnt wire and had to replace it as well. Started system to find working to best of ability. The blower motor is running but client stated not blowing as hard as it use to. Checked and found blower motor is running and spinning but advised could be from improper air flow. Advised that if the motor goes out he should really consider system replacement due to age and cost of repairs Task Includes -Installation of new disconnect

Power outage reprogrammed thermostat

Found clogged condenser coils Client is cleaning

Came out for a maintenance upon arrival customer had concern about water and float switch clear drain no problem at this time. Need to go over with customer options of repair versus place for low refrigerant and machine is not keeping up during hot time of the day

Arrived to find float switch tripped due to clogged primary drain line. Advised client how bad drain line was clogged and how bad condenser coils was desbris up offered maint plan and a in line drain cleanser to assure drain line will stay cleaned when we are not out onsite servicing system. Client wished to only due bare minimum today and clear the drain line. Performed the below Task Includes -Clearing and treating condensation line

Moved dryer vent

Task Includes Cleaning and disinfecting drain line *** Note this is a temporary fix due to condition of evaporator coil and needs pulling and cleaning*** Client stated they do want to perform the second option I have provided but need to wait roughly a week and made aware when estimate is signed and work is approved we would deduct 150$ from bill as proposal states within reasonable time

Task Includes -Installation of new Carrier 3 Ton Heat Pump System -Connecting to existing copper line set, drain line, and duct work. -10 year parts 1 year labor warranty -All permits and inspections included -Enlarging return air from 24x18 to 24x20 -Free UV replacement bulb

Included: New furnace New evaporator coil New condenser 10 year parts warranty 1 year Labor warranty 1 year maintenance Permits and inspections Warranty registration Removal and disposal of old equipment and materials New thermostat Furnace platform Hurricane pad and tie downs New condenser power cord Gas piping Furnace exhaust piping to ceiling Duct clean Duct sanitation Float switches Lineset flush Drain line flush Project is funded via upgrade. The job is scheduled for 11/21

Brennan G Today I visited for the system not cooling and leaking water. I discovered the emergency pan was over flowing and the float sensors were no longer shutting the system down. I did not see the water leak from the air handler into the pan, I am unsure why the water ended up in the pan. I replaced both float switches and cleared the drain line. I also reduced the blower speed to T3 in order to reduce air pressure that may have caused the water to drain improperly. I watched the system run and drain normally before leaving.

Brennan G Today I visited for furnace making and loud nouse and the system operating inefficiently. We discovered the blower assembly has failed and the system is not moving the proper amount of air to sufficiently cool the home. I also discovered many other concerns regarding the equipments efficiency and saftey. Due to the age and repair cost Meera elected to have us replace the system. The job is being funded via upgrade and is scheduled for 11/21.

Arrived to find thermostat set at 72 and satisfied at 72 Inspected entire system to find super heat slightly low and only a 3 degree subcool. Manufacture data plate states they want a 14-16 degree superheat and 7-9 subcool. Adjusted txv and added Freon accordingly to achieve manufacturer specs. All is now cooong as designed and has dropped temp to 69 inside.

Returned and replaced 3 ton daikin system with new 3.5 ton Goodman system. This is the system the owner originally payed for . Assured proper cooling and draining

James Returned and evacuated system Removed OEM filter dryer Brazed in new filter dryer Pressurized system with nitrogen to assure no leaks Pulled required 500 micron vac Charged system with weighed out charge and system is now performing as designed.

Brennan G Today I visited for the system not cooling. I discovered the contactor relay was burnt and needed to be replaced and have minor wiring repairs done. I made the necessary repairs to get the system operational. The system is now cooling. We discussed future services the system should have done and also discussed enrolling into our maintenance agreement. I gave the member discount as a courtesy. I emailed the invoice for payment.